User Manual Avery Dennison 6404 The printer is an Avery-Dennison 64-04. For best printing performance, we recommend the use of the latest NiceDriver for your. Owners Manual Avery Dennison 6404 The printer is an Avery-Dennison 64-04. I set the top of form manually before starting to print. The first label prints OK, but successive labels are misaligned. Looking for a manual for your printer? Search on a printer model number and all of the documentation related to that printer will be listed. Active Model Search. Free to download, have your printer running like a champ! Monarch and Avery Dennison Hand Labelers. Avery Dennison Monarch 9864 Error Messages User Manual. 4104 olv timeout, 4105 no olv response, Occur with olv-option, No olv data, Olv limit exceed, Olv barcode. Avery Dennison 64-04 Printer. Optimum supply chain management is vital if you are to survive in today's market. And to achieve it, efficiency, reduced costs and end-to-end traceability are required. A professional label is the key to greater efficiency in the supply chain; but only if the label itself is produced efficiently. USER MANUAL Fig.: 64-04 (Delivered version may deviate from the picture) Device classification Topic sections. 6.01-01 USER + SERVICE MANUAL /Using the Documentation All devices 6 Start page The start page is also only an organisational component and is displayed.
Advertising
TC9864CSQR Rev. AA 6/08
©2008 Avery Dennison Corp All rights reserved.
A64 CS Stacker Quick Reference
This Quick Reference contains supply loading information, setup, general care, and maintenance procedures for
the Avery Dennison® A64 Cutter/Stacker. For more detailed information, refer to the Operator’s Handbook
available on our Web site (www.monarch.com).
Information in this document supercedes information in previous versions. Check our Web site for the latest
documentation and release information.
Warning:
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instruction manuals, may cause interference to radio communications. It has been tested and
found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference in which case the user,
at his own expense, will be required to take whatever measures may be required to correct the interference.
the Avery Dennison® A64 Cutter/Stacker. For more detailed information, refer to the Operator’s Handbook
available on our Web site (www.monarch.com).
Information in this document supercedes information in previous versions. Check our Web site for the latest
documentation and release information.
Warning:
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instruction manuals, may cause interference to radio communications. It has been tested and
found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference in which case the user,
at his own expense, will be required to take whatever measures may be required to correct the interference.
G e t t i n g S t a r t e d
1. Set up your printer. Refer to the documentation provided with your printer for more information.
2. Unpack the stacker and packing material from the box.
The box should contain:
• Stacker base and tray assembly (with the “Stacker Full” cable attached to tray)
• Power cord and stacker interface cable
3. Set the stacker to the left side of the printer.
4. Alignment the printer to the stacker.
5. Attach the stacker tray assembly.
• Align the slotted holes of the tray with the studs on the stacker base.
• Align the fingers of the tray with grooves on the top rollers.
• Center the two screw holes and start the captive screws from underneath the base. Make
sure the tray fingers do not touch the black transport roller.
• Tighten the screws.
Avery Dennison Locations
Studs
Studs
Slotted Holes
Underside of Tray
Top view of Base
Screw Holes
Captive Screws
Advertising
Popular Brands
Popular manuals
Page 33: 4104 olv timeout, 4105 no olv response, Occur with olv-option, No olv data, Olv limit exceed, Olv barcode type, Olv timeout
Advertising
05/08 Rev. AB
USER MANUAL
Error Messages
9844 – 9854 – 9864
33
4100-4106
Messages which can only occur with OLV-Option
4100
No OLV data
Status
The verifier detects the bar code type and/or the bar code data, which was
just printed and read, does not match the bar code specified in the print job.
The error may have one of the following causes:
just printed and read, does not match the bar code specified in the print job.
The error may have one of the following causes:
•
verifier is not connected/enabled
•
The bar code has not been printed
•
The bar code has been printed poorly, so the verifier cannot detect it.
Action
Check if the verifier is connected properly
Check the printout quality. If the printout is poor, change the print
parameters and/or use a different material/ribbon-combination.
Perform a printhead dot check. There may be a defective dot.
If the bar code has not been printed at all: check the print job.
4101
OLV limit exceed
Status
The read bar code exceeds a user-specified limit. The limits (contrast or
readability), can be set via the parameter menu or via Easy Plug command.
readability), can be set via the parameter menu or via Easy Plug command.
Action
Check the printout quality.
Change the limit.
Change the print parameters or the material/ribbon combination.
4103
OLV barcode type
Status
The verifier detects the bar code type, which was just printed and read,
does not match the bar code specified in the print job.
does not match the bar code specified in the print job.
Action
Check the printout.
4104 OLV
Timeout
Status
General software error
Action
See notes in “General software errors” section.
4105
No OLV response
Status
This error occurs after turning on the printer with the verifier already turned
on. The verifier's version number was not successfully read.
on. The verifier's version number was not successfully read.
The error may have one of the following causes:
•
Wrong connection cable between verifier and printer
•
Invalid interface parameter setting for Com2
•
Verifier's power supply interrupted or not available
•
Defective I/O board (Com2)
Action
Check the possible causes of failure and exchange defective parts.
Advertising
Popular Brands
Avery Dennison 64-04 User Manual Free
Popular manuals